User:GNUtoo: Difference between revisions

From flashrom
Jump to navigation Jump to search
(→‎Mainboard based programmers: sort alphabetically)
Line 40: Line 40:
|
|
* Works with coreboot
* Works with coreboot
|-
| PC Engines Alix.1c
|
|
* Works with coreboot
* Works with the recovery LPC dongle
|-
|-
|-
| Lenovo Thinkpad X60
| Lenovo Thinkpad X60
Line 59: Line 52:
|
|
* Works with coreboot
* Works with coreboot
|-
| PC Engines Alix.1c
|
|
* Works with coreboot
* Works with the recovery LPC dongle
|-
|-
| PC Engines APU1D4
| PC Engines APU1D4

Revision as of 13:04, 27 February 2018

I've no code in flashrom yet, but I made a flashrom compatible arduino programmer and participated in testing and documentation.

Wiki contributions

My contributions to this wiki are available under the following licenses:

My interests

  • Easily available external flashers.
  • BIOS->Coreboot flashing on the Libreboot compatible laptops.
  • NIC flashing (to flash ipxe)
  • GPU flashing (to flash sgabios)


My hardware

Mainboard based programmers

Device or programmer Flash chip Test result
Asrock E350M1
  • A25L032
  • Works from coreboot
  • Untested from the BIOS
Asus M4A785T-M mainboard
  • W25x80 (DIP8)
  • Works with the BIOS
  • Works with coreboot
Lenovo Thinkpad T60
  • MX25L1605D/MX25L1608D
  • Works with coreboot
Lenovo Thinkpad X60
  • SST25VF016B
  • Works with coreboot.
Lenovo X60T
  • MX25L1605D/MX25L1608D
  • Works with coreboot
PC Engines Alix.1c
  • Works with coreboot
  • Works with the recovery LPC dongle
PC Engines APU1D4

External programmers

Device or programmer Status
Arduino uno (serprog)
  • Requires a 5v->3.3v level shifter for most current flash chips.
  • Issues with the 8u2/8u3 when using the serial port at high speed.
Arduino duemillanove (serprog)
  • Requires a 5v->3.3v level shifter for most current flash chips.
  • Works fine otherwise.
Arduino Due ( no support for it yet )
  • 3.3v level output on SPI.
  • Not working: No support for it yet.
openmoko debug board (ft2232_spi:type=openmoko)
  • Works fine
3com PCI NIC (10b7:9200) (nic3com)
  • Works fine
Sata SII PCI card
  • writing and erasing worked fine.
Really old PCI realtek cards
  • No parallel chip to test
Some GNU/Linux embedded boards (linux_spi)
  • Backporting some mainline kernel patches is required on some very old (2.6.35) kernel for omap3.
  • Works fine otherwise
An atahpt PCI card
  • Didn't work when adding the PCI IDS, but the atahpt is known not to work according to the mailing list.
old AGP Nvidia card
  • Worked with a patch (documented below)
Nvidia geforce 210 PCIe 16x card
  • didn't work when adding the PIC IDs

I've also the following hardware:

  • pomona clip for recovering my x60
  • some chips(2MB SO8(currently soldered), 16MB SO8)

Work in progress for the wiki

Don't try that, it's dangerous!!!!

Howto(Dangerous, not ready for the wiki)

Retrieved from "https://wiki.flashrom.org/index.php?title=User:GNUtoo&oldid=2296"